RAN CTD Profile Data - HMAS MELVILLE ProjectID: HI453MEL_M From: 2008-07-01 To: 2008-09-01
Updated: 2018-10-05
This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 322 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI453MEL_M from HMAS MELVILLE. The CTD was manufactured by Applied Microsystems Limited and is the "Micro CTD" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor. The CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity. The CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail. This type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process. Raw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts.
Data
- Link to CTD data in netCDF
- Data quality notes
- Full metadata link
- http://i.creativecommons.org/l/by/2.5/au/88x31.png
- http://creativecommons.org/licenses/by/2.5/au/
- {"title":"Royal Australian Navy (RAN) - CTD profiles","recordAbstract":"The Royal Australian Navy (RAN) collected vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe from RAN Hydrographic Survey cruises, between 2004 and 2016. There were 2 types of CTD used, the 'HS_CTD' used on smaller vessels which is lowered by a hand driven winch and the 'MVP200' CTD used on larger vessels and lowered by an electric winch. The CTD data is available as quality controlled netCDF files online at the AODN THREDDS server at http://thredds.aodn.org.au/thredds/ and also through a Web Map Service (WMS) at http://geoserver-123.aodn.org.au/geoserver. There are also metadata records, 1 per ship cruise, available at http://www.http://catalogue.aodn.org.au/geonetwork. The 2 CTD types are distinguished from one another by netCDF file naming or in the metadata record title element Data from the HS_CTD will have '_H' in the filename while MVP200 will have '_M'. HS_CTD The HS_CTD probe is manufactured by Falmouth Scientific and is the \"2-inch Micro CTD\" model. This CTD type is referred to operationally as the HS_CTD. This CTD is fitted within an inductive type conductivity cell, a platinum thermometer and silicon pressure sensor. The CTD temperature sensor is calibrated on the ITS-90 temperature scale against a master CTD using a controlled temperature bath. The pressure sensor is calibrated using a Druck Pressure Calibrator. The conductivity sensor is calibrated in a temperature controlled bath against seawater samples of known conductivity. The HS_CTD is lowered and raised by a hand winch sampling at a rate of 1.83 Hz. Data files were recorded in the downcast and upcast direction but most data is from downcasts due to higher quality. Raw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals and converted to netCDF format files. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts. MVP200 CTD The MVP200 CTD is manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor. The CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity. The CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater so most data available are downcast files. This type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the 'Data Quality - Lineage section' for further details on the salinity de-spiking process. Raw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS LEEUWIN ProjectID: HI456LEE_M From: 2008-09-15 To: 2008-10-20","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 24 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI456LEE_M from HMAS LEEUWIN.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS LEEUWIN ProjectID: HI454LEE_H From: 2008-06-16 To: 2008-07-02","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 7 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI454LEE_H from HMAS LEEUWIN. \n\nThe CTD was manufactured by Falmouth Scientific and is the \"2-inch Micro CTD\" model. This CTD type is referred to operationally as the HS_CTD. This CTD is fitted within an inductive type conductivity cell, a platinum thermometer and silicon pressure sensor.\n\nThe CTD temperature sensor is calibrated on the ITS-90 temperature scale against a master CTD using a controlled temperature bath. The pressure sensor is calibrated using a Druck Pressure Calibrator. The conductivity sensor is calibrated in a temperature controlled bath against seawater samples of known conductivity.\n\nThe HS_CTD is lowered and raised by a hand winch sampling at a rate of 1.83 Hz. Data files were recorded in the downcast and upcast direction but most data is from downcasts due to higher quality. Raw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals and converted to netCDF format files. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS LEEUWIN ProjectID: HI444LEE_M From: 2007-07-05 To: 2007-09-02","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 371 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI444LEE_M from HMAS LEEUWIN.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS LEEUWIN ProjectID: HI454LEE_M From: 2008-06-23 To: 2008-07-24","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 112 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI454LEE_M from HMAS LEEUWIN.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS MELVILLE ProjectID: HI384MEL_H From: 2004-01-25 To: 2004-03-24","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 32 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI384MEL_H from HMAS MELVILLE. \n\nThe CTD was manufactured by Falmouth Scientific and is the \"2-inch Micro CTD\" model. This CTD type is referred to operationally as the HS_CTD. This CTD is fitted within an inductive type conductivity cell, a platinum thermometer and silicon pressure sensor.\n\nThe CTD temperature sensor is calibrated on the ITS-90 temperature scale against a master CTD using a controlled temperature bath. The pressure sensor is calibrated using a Druck Pressure Calibrator. The conductivity sensor is calibrated in a temperature controlled bath against seawater samples of known conductivity.\n\nThe HS_CTD is lowered and raised by a hand winch sampling at a rate of 1.83 Hz. Data files were recorded in the downcast and upcast direction but most data is from downcasts due to higher quality. Raw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals and converted to netCDF format files. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS MERMAID ProjectID: HI518MER_M From: 2012-03-08 To: 2012-04-01","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 25 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI518MER_M from HMAS MERMAID.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS LEEUWIN ProjectID: HI416LEE_H From: 2006-02-09 To: 2006-04-23","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 8 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI416LEE_H from HMAS LEEUWIN. \n\nThe CTD was manufactured by Falmouth Scientific and is the \"2-inch Micro CTD\" model. This CTD type is referred to operationally as the HS_CTD. This CTD is fitted within an inductive type conductivity cell, a platinum thermometer and silicon pressure sensor.\n\nThe CTD temperature sensor is calibrated on the ITS-90 temperature scale against a master CTD using a controlled temperature bath. The pressure sensor is calibrated using a Druck Pressure Calibrator. The conductivity sensor is calibrated in a temperature controlled bath against seawater samples of known conductivity.\n\nThe HS_CTD is lowered and raised by a hand winch sampling at a rate of 1.83 Hz. Data files were recorded in the downcast and upcast direction but most data is from downcasts due to higher quality. Raw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals and converted to netCDF format files. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS PALUMA ProjectID: HI570PAL_M From: 2015-05-10 To: 2015-07-06","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 97 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI570PAL_M from HMAS PALUMA.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS BENALLA ProjectID: HI568BEN_M From: 2015-02-26 To: 2015-04-14","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 231 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI568BEN_M from HMAS BENALLA.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS LEEUWIN ProjectID: HI488LEE_M From: 2011-01-11 To: 2011-01-11","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 1 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI488LEE_M from HMAS LEEUWIN.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS MELVILLE ProjectID: HI509MEL_M From: 2012-01-09 To: 2012-02-26","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 611 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI509MEL_M from HMAS MELVILLE.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS LEEUWIN ProjectID: HI446(C)LEE_H From: 2009-02-04 To: 2009-02-05","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 2 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI446(C)LEE_H from HMAS LEEUWIN. \n\nThe CTD was manufactured by Falmouth Scientific and is the \"2-inch Micro CTD\" model. This CTD type is referred to operationally as the HS_CTD. This CTD is fitted within an inductive type conductivity cell, a platinum thermometer and silicon pressure sensor.\n\nThe CTD temperature sensor is calibrated on the ITS-90 temperature scale against a master CTD using a controlled temperature bath. The pressure sensor is calibrated using a Druck Pressure Calibrator. The conductivity sensor is calibrated in a temperature controlled bath against seawater samples of known conductivity.\n\nThe HS_CTD is lowered and raised by a hand winch sampling at a rate of 1.83 Hz. Data files were recorded in the downcast and upcast direction but most data is from downcasts due to higher quality. Raw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals and converted to netCDF format files. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS MELVILLE ProjectID: HI399MEL_H From: 2000-11-01 To: 2004-12-16","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 48 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI399MEL_H from HMAS MELVILLE. \n\nThe CTD was manufactured by Falmouth Scientific and is the \"2-inch Micro CTD\" model. This CTD type is referred to operationally as the HS_CTD. This CTD is fitted within an inductive type conductivity cell, a platinum thermometer and silicon pressure sensor.\n\nThe CTD temperature sensor is calibrated on the ITS-90 temperature scale against a master CTD using a controlled temperature bath. The pressure sensor is calibrated using a Druck Pressure Calibrator. The conductivity sensor is calibrated in a temperature controlled bath against seawater samples of known conductivity.\n\nThe HS_CTD is lowered and raised by a hand winch sampling at a rate of 1.83 Hz. Data files were recorded in the downcast and upcast direction but most data is from downcasts due to higher quality. Raw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals and converted to netCDF format files. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS LEEUWIN ProjectID: HI460(A)LEE_H From: 2009-09-03 To: 2009-09-10","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 11 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI460(A)LEE_H from HMAS LEEUWIN. \n\nThe CTD was manufactured by Falmouth Scientific and is the \"2-inch Micro CTD\" model. This CTD type is referred to operationally as the HS_CTD. This CTD is fitted within an inductive type conductivity cell, a platinum thermometer and silicon pressure sensor.\n\nThe CTD temperature sensor is calibrated on the ITS-90 temperature scale against a master CTD using a controlled temperature bath. The pressure sensor is calibrated using a Druck Pressure Calibrator. The conductivity sensor is calibrated in a temperature controlled bath against seawater samples of known conductivity.\n\nThe HS_CTD is lowered and raised by a hand winch sampling at a rate of 1.83 Hz. Data files were recorded in the downcast and upcast direction but most data is from downcasts due to higher quality. Raw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals and converted to netCDF format files. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS LEEUWIN ProjectID: HI460(A)LEE_M From: 2009-09-02 To: 2009-09-11","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 182 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI460(A)LEE_M from HMAS LEEUWIN.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS PALUMA ProjectID: HI580PAL_M From: 2015-09-05 To: 2015-10-15","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 45 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI580PAL_M from HMAS PALUMA.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS SHEPPARTON ProjectID: HI554SHE_M From: 2014-07-10 To: 2014-08-04","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 163 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI554SHE_M from HMAS SHEPPARTON.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - SMB DUYFKEN ProjectID: HI461DUY_H From: 2009-04-20 To: 2009-05-14","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 8 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI461DUY_H from SMB DUYFKEN. \n\nThe CTD was manufactured by Falmouth Scientific and is the \"2-inch Micro CTD\" model. This CTD type is referred to operationally as the HS_CTD. This CTD is fitted within an inductive type conductivity cell, a platinum thermometer and silicon pressure sensor.\n\nThe CTD temperature sensor is calibrated on the ITS-90 temperature scale against a master CTD using a controlled temperature bath. The pressure sensor is calibrated using a Druck Pressure Calibrator. The conductivity sensor is calibrated in a temperature controlled bath against seawater samples of known conductivity.\n\nThe HS_CTD is lowered and raised by a hand winch sampling at a rate of 1.83 Hz. Data files were recorded in the downcast and upcast direction but most data is from downcasts due to higher quality. Raw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals and converted to netCDF format files. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS MELVILLE ProjectID: HI475MEL_M From: 2010-05-17 To: 2010-05-25","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 198 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI475MEL_M from HMAS MELVILLE.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - SMB DUYFKEN ProjectID: HI472DUY_H From: 2010-02-23 To: 2010-04-11","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 7 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI472DUY_H from SMB DUYFKEN. \n\nThe CTD was manufactured by Falmouth Scientific and is the \"2-inch Micro CTD\" model. This CTD type is referred to operationally as the HS_CTD. This CTD is fitted within an inductive type conductivity cell, a platinum thermometer and silicon pressure sensor.\n\nThe CTD temperature sensor is calibrated on the ITS-90 temperature scale against a master CTD using a controlled temperature bath. The pressure sensor is calibrated using a Druck Pressure Calibrator. The conductivity sensor is calibrated in a temperature controlled bath against seawater samples of known conductivity.\n\nThe HS_CTD is lowered and raised by a hand winch sampling at a rate of 1.83 Hz. Data files were recorded in the downcast and upcast direction but most data is from downcasts due to higher quality. Raw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals and converted to netCDF format files. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS LEEUWIN ProjectID: HI472LEE_H From: 2010-02-23 To: 2010-02-27","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 4 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI472LEE_H from HMAS LEEUWIN. \n\nThe CTD was manufactured by Falmouth Scientific and is the \"2-inch Micro CTD\" model. This CTD type is referred to operationally as the HS_CTD. This CTD is fitted within an inductive type conductivity cell, a platinum thermometer and silicon pressure sensor.\n\nThe CTD temperature sensor is calibrated on the ITS-90 temperature scale against a master CTD using a controlled temperature bath. The pressure sensor is calibrated using a Druck Pressure Calibrator. The conductivity sensor is calibrated in a temperature controlled bath against seawater samples of known conductivity.\n\nThe HS_CTD is lowered and raised by a hand winch sampling at a rate of 1.83 Hz. Data files were recorded in the downcast and upcast direction but most data is from downcasts due to higher quality. Raw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals and converted to netCDF format files. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS LEEUWIN ProjectID: HI444LEE_H From: 2007-07-30 To: 2007-08-10","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 7 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI444LEE_H from HMAS LEEUWIN. \n\nThe CTD was manufactured by Falmouth Scientific and is the \"2-inch Micro CTD\" model. This CTD type is referred to operationally as the HS_CTD. This CTD is fitted within an inductive type conductivity cell, a platinum thermometer and silicon pressure sensor.\n\nThe CTD temperature sensor is calibrated on the ITS-90 temperature scale against a master CTD using a controlled temperature bath. The pressure sensor is calibrated using a Druck Pressure Calibrator. The conductivity sensor is calibrated in a temperature controlled bath against seawater samples of known conductivity.\n\nThe HS_CTD is lowered and raised by a hand winch sampling at a rate of 1.83 Hz. Data files were recorded in the downcast and upcast direction but most data is from downcasts due to higher quality. Raw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals and converted to netCDF format files. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS MELVILLE ProjectID: HI453MEL_H From: 2008-07-14 To: 2008-08-25","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 13 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI453MEL_H from HMAS MELVILLE. \n\nThe CTD was manufactured by Falmouth Scientific and is the \"2-inch Micro CTD\" model. This CTD type is referred to operationally as the HS_CTD. This CTD is fitted within an inductive type conductivity cell, a platinum thermometer and silicon pressure sensor.\n\nThe CTD temperature sensor is calibrated on the ITS-90 temperature scale against a master CTD using a controlled temperature bath. The pressure sensor is calibrated using a Druck Pressure Calibrator. The conductivity sensor is calibrated in a temperature controlled bath against seawater samples of known conductivity.\n\nThe HS_CTD is lowered and raised by a hand winch sampling at a rate of 1.83 Hz. Data files were recorded in the downcast and upcast direction but most data is from downcasts due to higher quality. Raw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals and converted to netCDF format files. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS LEEUWIN ProjectID: HI500LEE_M From: 2011-08-30 To: 2011-09-27","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 61 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI500LEE_M from HMAS LEEUWIN.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - SMB CASUARINA ProjectID: HI446(C)CAS_H From: 2009-01-18 To: 2009-02-22","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 36 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI446(C)CAS_H from SMB CASUARINA. \n\nThe CTD was manufactured by Falmouth Scientific and is the \"2-inch Micro CTD\" model. This CTD type is referred to operationally as the HS_CTD. This CTD is fitted within an inductive type conductivity cell, a platinum thermometer and silicon pressure sensor.\n\nThe CTD temperature sensor is calibrated on the ITS-90 temperature scale against a master CTD using a controlled temperature bath. The pressure sensor is calibrated using a Druck Pressure Calibrator. The conductivity sensor is calibrated in a temperature controlled bath against seawater samples of known conductivity.\n\nThe HS_CTD is lowered and raised by a hand winch sampling at a rate of 1.83 Hz. Data files were recorded in the downcast and upcast direction but most data is from downcasts due to higher quality. Raw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals and converted to netCDF format files. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS PALUMA ProjectID: HI559PAL_M From: 2014-08-26 To: 2014-09-19","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 6 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI559PAL_M from HMAS PALUMA.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS LEEUWIN ProjectID: SRATA-0252LEE_M From: 2014-08-18 To: 2014-09-15","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 322 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise SRATA-0252LEE_M from HMAS LEEUWIN.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS LEEUWIN ProjectID: HI461LEE_H From: 2009-05-10 To: 2009-05-11","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 3 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI461LEE_H from HMAS LEEUWIN. \n\nThe CTD was manufactured by Falmouth Scientific and is the \"2-inch Micro CTD\" model. This CTD type is referred to operationally as the HS_CTD. This CTD is fitted within an inductive type conductivity cell, a platinum thermometer and silicon pressure sensor.\n\nThe CTD temperature sensor is calibrated on the ITS-90 temperature scale against a master CTD using a controlled temperature bath. The pressure sensor is calibrated using a Druck Pressure Calibrator. The conductivity sensor is calibrated in a temperature controlled bath against seawater samples of known conductivity.\n\nThe HS_CTD is lowered and raised by a hand winch sampling at a rate of 1.83 Hz. Data files were recorded in the downcast and upcast direction but most data is from downcasts due to higher quality. Raw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals and converted to netCDF format files. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS MERMAID ProjectID: HI546MER_M From: 2014-01-15 To: 2014-02-04","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 47 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI546MER_M from HMAS MERMAID.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS LEEUWIN ProjectID: HI488LEE_H From: 2011-02-12 To: 2011-02-21","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 2 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI488LEE_H from HMAS LEEUWIN. \n\nThe CTD was manufactured by Falmouth Scientific and is the \"2-inch Micro CTD\" model. This CTD type is referred to operationally as the HS_CTD. This CTD is fitted within an inductive type conductivity cell, a platinum thermometer and silicon pressure sensor.\n\nThe CTD temperature sensor is calibrated on the ITS-90 temperature scale against a master CTD using a controlled temperature bath. The pressure sensor is calibrated using a Druck Pressure Calibrator. The conductivity sensor is calibrated in a temperature controlled bath against seawater samples of known conductivity.\n\nThe HS_CTD is lowered and raised by a hand winch sampling at a rate of 1.83 Hz. Data files were recorded in the downcast and upcast direction but most data is from downcasts due to higher quality. Raw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals and converted to netCDF format files. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS MELVILLE ProjectID: HI431MEL_M From: 2007-02-16 To: 2007-03-06","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 134 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI431MEL_M from HMAS MELVILLE.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS PALUMA ProjectID: HI526PAL_M From: 2013-05-06 To: 2013-05-08","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 12 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI526PAL_M from HMAS PALUMA.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS MERMAID ProjectID: HI526MER_M From: 2013-05-06 To: 2013-06-03","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 31 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI526MER_M from HMAS MERMAID.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS MELVILLE ProjectID: SRATA-0135MEL_M From: 2008-01-17 To: 2008-01-20","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 86 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise SRATA-0135MEL_M from HMAS MELVILLE.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS SHEPPARTON ProjectID: HI558SHE_M From: 2014-10-17 To: 2014-11-28","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 224 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI558SHE_M from HMAS SHEPPARTON.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS LEEUWIN ProjectID: HI556LEE_M From: 2014-10-18 To: 2014-12-07","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 190 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI556LEE_M from HMAS LEEUWIN.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS MELVILLE ProjectID: HI446(B)MEL_M From: 2008-10-29 To: 2008-12-05","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 32 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI446(B)MEL_M from HMAS MELVILLE.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS MELVILLE ProjectID: HI571MEL_M From: 2015-05-03 To: 2015-06-05","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 139 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI571MEL_M from HMAS MELVILLE.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS PALUMA ProjectID: HI546PAL_M From: 2014-01-24 To: 2014-02-12","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 23 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI546PAL_M from HMAS PALUMA.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}
- {"title":"RAN CTD Profile Data - HMAS PALUMA ProjectID: HI544PAL_M From: 2014-04-09 To: 2014-06-04","recordAbstract":"This dataset contains quality controlled vertical profiles of pressure, temperature and salinity measured by a Conductivity, Temperature and Depth (CTD) probe. The dataset contains 76 CTD profiles (casts) obtained during RAN Hydrographic Survey cruise HI544PAL_M from HMAS PALUMA.\n\nThe CTD was manufactured by Applied Microsystems Limited and is the \"Micro CTD\" model. This CTD type is referred to operationally as the MVP200_CTD. This CTD is fitted with a 4 electrode platinized conductivity cell, thermistor temperature sensor and a semiconductor strain gauge pressure sensor.\n\nThe CTD sensors are calibrated at the manufacturer Applied Microsystems Limited on a 12-18 month schedule. The CTD temperature sensor is calibrated against 'Hart' temperature standards. The pressure sensor is calibrated using 'Budenburg Deadweight' standards. The conductivity sensor is calibrated using 'Hart' temperature standards and seawater samples of known conductivity.\n\nThe CTD sensors are mounted to a fish-shape probe. The probe is controlled by an electric winch (MVP200 type). For downcasts the fish is allowed to free-fall (winch is in 'free-wheel' mode) under its own weight at about 2-3 ms-1 and then is winched back. Data is recorded in downcast and usually in upcast direction at a sampling rate of 25 Hz. The downcast data is of higher quality because sensors encounter undisturbed seawater that flows through the nose of the fish. On the upcast the fish is flipped around (tail first) and the sensors in the nose encounter disturbed flow from the fish tail.\n\nThis type of CTD is prone to a phenomenon called 'salinity spiking' caused by a mismatch between the response times of the temperature and conductivity sensor. Data undergoes a salinity de-spiking routine to correct for this. See the history metadata for further details on the salinity de-spiking process.\n\nRaw CTD pressure data is not always monotonic due to transient up/down motion of winch/ship. Raw pressure data is subsetted to give a monotonic (increasing) sequence and then linearly interpolated to 1 decibar pressure intervals. Data is then flagged with quality control flags after visual inspection and comparison to average climatology and historical CTD casts."}